0281012284 P05094331AF – ecu engine controller Jeep 3.0 CRD VIRGIN for programming
We offer a tested ecu engine controller Jeep 3.0 CRD with references Bosch 0281012284 and Mopar P05094331AF. The module carries the designation 331AF and has been prepared in VIRGIN condition, meaning it is a reset ECU ready for programming in another vehicle. The product has been electronically tested before dispatch and is supplied with warranty.
Application of the 0281012284 / P05094331AF ecu
The 0281012284 ecu engine controller is used in selected Jeep vehicles equipped with the 3.0 CRD V6 diesel engine. It is most commonly found in models where it controls fuel injection, turbocharger operation, immobiliser functions and communication with other vehicle modules.
- Brand: Jeep
- Model: selected Jeep Grand Cherokee 3.0 CRD versions
- Engine: 3.0 CRD V6 diesel
- Bosch reference: 0281012284
- Mopar / Chrysler reference: P05094331AF
- Designation: 331AF
- Condition: VIRGIN – reset and ready for programming
The most important compatibility requirement is matching the numbers from the original ECU. If the original module installed in the vehicle has the reference 0281012284, P05094331AF or designation 331AF, this ECU may be the correct replacement after proper programming.
VIRGIN – ready for adaptation in the vehicle
This Jeep P05094331AF ecu engine controller has been prepared in VIRGIN condition. This means it no longer contains immobiliser data from the previous vehicle and can be programmed to another car. It is not a Plug & Play version — coding and adaptation are required after installation.
Programming is performed using a diagnostic tool compatible with Jeep / Chrysler / Dodge vehicles, most commonly service devices such as WiTECH, StarSCAN, StarMOBILE or compatible diagnostic programmers supporting ECU coding and immobiliser synchronisation. During the procedure, the ECU is assigned to the vehicle, synchronised with the immobiliser and configured according to the vehicle equipment.
Most common symptoms of faulty Jeep 3.0 CRD ecu
A damaged 0281012284 / P05094331AF ecu engine controller may cause engine starting problems, lack of diagnostic communication, immobiliser faults, CAN communication errors, engine stalling, injector control failure or internal ECU errors. Failure may result from electrical short circuits, voltage spikes, moisture, wiring damage, power supply issues or unsuccessful previous programming attempts.
Bosch 0281012284 ecu – tested and covered by warranty
The offered Bosch 0281012284 / P05094331AF module has been electronically tested and prepared as a clean VIRGIN ecu engine controller. It is a good solution in cases of damaged original ECU, inability to read data from the original controller or replacement after electronic failure. Before purchase, we recommend comparing all numbers from the original ECU label.
Q&A – frequently asked questions
Does the 0281012284 ecu fit Jeep Grand Cherokee 3.0 CRD?
The 0281012284 ecu engine controller may fit selected Jeep Grand Cherokee 3.0 CRD versions, but the most important factor is matching both the Bosch and Mopar references. If the original module carries P05094331AF or 331AF, compatibility is much more likely.
Is the P05094331AF ecu Plug & Play?
No. This P05094331AF ecu has been prepared in VIRGIN condition and requires programming after installation. After proper adaptation, it will operate like a correctly assigned original engine controller.
Which tool can program the Jeep 3.0 CRD 331AF ecu?
To program the 331AF ecu, it is recommended to use a diagnostic tool supporting Jeep / Chrysler vehicles, such as WiTECH, StarSCAN, StarMOBILE or a compatible device capable of ECU coding and immobiliser synchronisation.
What does VIRGIN mean for the 0281012284 ecu?
VIRGIN means that the Bosch 0281012284 ecu has been reset and cleared of immobiliser data from the previous vehicle, making it ready for programming in another car.
Can this ecu help if the original Jeep 3.0 CRD ECU has no communication?
Yes, the P05094331AF ecu may be a good solution if the original controller no longer communicates, provided the references match and correct programming is performed after installation.
