Skip to main content
English €
Open search engine
Search
Close search engine Clear Search
Products in the cart: 0. See details
Your cart is empty

Replacing ABS Pump 1K0614517 – VCDS Coding and Sensor Calibration Step by Step

After replacing a 1K0614517 ABS pump in a VW, Audi, Seat or Škoda, it has to be coded. The best way is to transfer the coding from the old pump and then calibrate the sensors, including the steering angle sensor.

We show the order of steps in VCDS and explain how to match the pump by the numbers on its label.

  • author: EcuSale
  • added: 14-11-2026
ABS pump with control module on a workshop bench – coding after replacement (VCDS)

A new or used ABS pump does not always work straight after it is bolted in. In VAG group cars the ABS unit has to be coded with a diagnostic tool and the sensors have to be calibrated.

At ECUSALE we stock many ATE pumps numbered 1K0614517 with the 1K0907379 control module, so here is how to code them after fitting. If you are still looking for the cause of the ABS light, start with our guide ABS pump failure – symptoms, repair or replacement.

Contents

  1. Does an ABS pump need coding after replacement?
  2. ABS pump coding in VCDS step by step
  3. How to choose the right ABS pump – this matters most
  4. 1K0614517 pumps – how to choose the right version
  5. Which cars do 1K0614517 pumps fit?
  6. Used or refurbished pump – what we check
  7. 6R0614117 pumps for Polo, Fabia and Ibiza
  8. ABS pumps for other makes
  9. Frequently asked questions

Does an ABS pump need coding after replacement?

It depends on the car and the pump version. In VW, Audi, Seat and Škoda cars with a 1K0614517 pump, coding is always needed. The ABS module receives your car's configuration and the sensors have to be calibrated.

Simply plugging in the connector is not enough, so plan the coding together with the fitting.

MK60 and MK60EC1 pumps always need coding and sensor calibration. Coding and sensor calibration are done on the car, after the pump has been fitted and the system bled. The most common mistake after fitting is incorrect sensor coding or a badly performed pump calibration, so it pays to follow the order described below.

ABS pump coding in VCDS step by step

You need a VCDS tool for the coding. Before you disconnect anything, run a full Auto-Scan. The rest of the procedure depends on the module version: MK60 or MK60EC1.

Step 1: full Auto-Scan before removal

  1. Connect VCDS and run a full Auto-Scan of the whole car while the old pump is still fitted.
  2. Save the report with the Save button. VCDS stores it as a text file in the Logs folder of the program directory. Copy the file to a USB stick or your phone as well.
  3. In the report, find address 03 – Brakes. Write down or photograph the module part number, the component name and the full coding.
  4. The component name tells you the version: MK60 or MK60EC1. The next steps depend on it.
  5. Fit the new pump and bleed the brake system.

Important: the G85 steering angle sensor always comes last. Calibrate G85 as the last basic setting, only after the other sensors have been adapted. If the steering angle sensor is not adapted correctly at the very end, the coding will be erased again once the ignition is switched off.

Step 2a: MK60 module – coding and sensor calibration

  1. If the module version allows the coding to be transferred, open address 03 and, in Coding – 07, enter the coding saved from the old pump. Exception: when replacing a 1K0907379D module with a 1K0907379K or newer, the coding has to be calculated from the car’s equipment.
  2. Log in with code 40168 (Coding-II – 11 or Security Access – 16).
  3. In Basic Settings – 04, first calibrate the other sensors: lateral acceleration G200 (group 063), brake pressure G201 (group 066) and longitudinal acceleration G251 (group 069) if the car has it. Before each calibration, check the measuring block given in the documentation.
  4. At the very end, as the last basic setting, calibrate the steering angle sensor G85 (group 060).
  5. Clear the fault codes and take a test drive.

Step 2b: MK60EC1 module – long coding and calibration

  1. Open address 03, go to long coding and enter the coding saved from the old pump in the New Coding field.
  2. Log in with code 40168 (Security Access) and calibrate the other sensors following the procedure for your version.
  3. Finally, prepare the calibration of the steering angle sensor G85: start the engine, turn the steering wheel one full turn in each direction, drive straight at no more than 20 km/h and stop with the wheels pointing straight ahead.
  4. Before starting the calibration, check measuring block 004: the value in field 1 must be between −1.5 and +1.5°.
  5. Run the basic settings in group 060. When they are done, field 2 should show OK.
  6. Then carry out the steering stop adaptation following the procedure for your car.
  7. Switch off the ignition, check that the coding has held, clear the fault codes and take a test drive.

What if the old module does not respond?

If the old module does not communicate with the tool, the Auto-Scan will not show its coding. Check whether you have an earlier Auto-Scan of the car, for example from a service visit – you can enter the coding saved there in the New Coding field. If there is no coding anywhere, prepare a full Auto-Scan of the car and its repair history and pass them to the technical support of your tool’s manufacturer. You can also send us the pump number before buying and we will advise you on what to do next.

Why is it best to transfer the coding from the old pump?

The old pump holds coding matched to your car. If you copy it to the new unit, you do not have to work it out from scratch. That is why it pays to read the coding before the old unit is disconnected.

How to choose the right ABS pump – this matters most

Choose the pump by its numbers, not by the car model. Every unit has two main numbers: the module number (1K0907379 with letters) and the pump number, i.e. the hydraulic block (1K0614517 with letters). Both must be the same as on your unit, including the letters at the end.

If the main pump number and the main module number are the same, the pump fits. The car model, make and trim level do not matter – the numbers do.

ATE ABS module label with number 1K0907379AD
Module label: the main number is 1K0 907 379 AD, under the word “Controller” (marked in red).
ABS pump sticker with number 1K0614517BJ
Pump (hydraulic block) sticker: the main number is 1K0 614 517 BJ, on the top line (marked in red).

The photos show example labels from two different units.

How to check it step by step

  1. Find the label on the plastic housing of the module and read the number under “Controller”.
  2. Find the sticker on the round pump motor and read the 1K0614517 number with its letters.
  3. Compare both numbers with the ones in our offer. They must match character for character, including the letters at the end.
  4. Not sure? Send us photos of both labels and we will check the match.

Not sure which pump fits?

Send a photo of your pump's label to sale@ecusale.com or on WhatsApp +48 888 638 546 (Mon–Fri, 9:00–16:00 Polish time). We will compare both numbers and point you to the right version.

1K0614517 pumps – how to choose the right version

The unit's label carries two numbers: 1K0614517 with letters at the end (hydraulic block) and 1K0907379 with letters (ABS control module). The 1K0614517 pump exists in many versions, and the full number including the letters decides the fit. The same pump number can work with an MK60 or an MK60EC1 module, so always compare the module number too.

These are the versions we have in stock:

Pump numberModule numberVersionPrice (approx.)
1K0614517BD – used, checked1K0907379ADused, checked445 €
1K0614517BD – refurbished1K0907379ADrefurbished495 €
1K0614517BJ1K0907379ANused, checked425 €
1K0614517BE / 1K0907379AJ – used, checked1K0907379AJused, checked280 €
1K0614517BE / 1K0907379AE – refurbished1K0907379AErefurbished590 €
1K0614517DE1K0907379BJused, checked210 €
1K0614517BK – refurbished1K0907379APrefurbished520 €
1K0614517BK – used, checked1K0907379APused, checked400 €
1K0614517CP1K0907379BEused, checked210 €
1K0614517CE1K0907379ATused, checked235 €
1K0614517AS1K0907379AHused, checked400 €
1K0614517DN1K0907379BKused, checked200 €
1K0614517ED1K0907379BMused, checked175 €
1K0614517DP1K0907379BLused, checked165 €

All VAG pumps are in the Volkswagen VW ABS pumps and Škoda ABS pumps categories.

Which cars do 1K0614517 pumps fit?

1K0614517 pumps were fitted to VAG group cars built on the PQ35 platform: VW, Audi, Seat and Škoda models. For several versions we have confirmed specific models:

Pump numberConfirmed models
1K0614517DEVW Golf VI, VW Touran (1T3), Audi A3 8P, Seat Leon II, Seat Altea, Škoda Octavia II, Škoda Superb II
1K0614517DPVW Golf VI / Golf Plus / Golf Variant, VW Touran (1T3), Škoda Octavia II, Škoda Superb II, Škoda Yeti
1K0614517EDVW Caddy III (2K, 2011–2015), VW Scirocco III, VW Golf VI
1K0614517CEVW Golf VI, VW Touran (1T3)
1K0614517BKVW Golf VI (2009–2013)
1K0614517CPVW Touran (1T3)

The other versions we stock (1K0614517BD, BE, BJ, AS, DN) also come from VAG PQ35 cars, but we match them by the label numbers only. The same car model may have had different pump versions depending on its equipment, so the pump and module numbers matter more than the make and year.

Used or refurbished pump – what we check

We prepare every 1K0614517 pump in one of two versions:

  • Used, checked – electronics and hydraulics checked on a test machine, including a pressure test.
  • Used and refurbished – we replace the processor in the control module with a new one. This is the most common fault in these units. The hydraulics are cleaned and pressure tested.

In both versions we also test the unit's sensors before the pump is shipped.

Approximate prices: used, checked pumps cost from about €165 to €445 depending on the version, and refurbished pumps about €495–590. For the same number, the refurbished version costs about €50–120 more, e.g. 1K0614517BD: €445 (used) and €495 (refurbished), 1K0614517BK: €400 and €520. The current price is always shown on the product page.

We sell complete units: the ABS module together with the hydraulic block. In refurbished pumps, besides replacing the processor and pressure-testing the block, we also check the pump motor and how the sensors work under load. If you would rather keep your own pump, we can repair it. Repair costs are covered in our ABS pump guide.

6R0614117 pumps for Polo, Fabia and Ibiza

Pumps 6R0614117 with the 6R0907379 module were fitted to cars including the VW Polo, Škoda Fabia II and Seat Ibiza. Here too the system has to be bled and the module coded after fitting, but the coding and calibration procedure depends on the module version. Read the version from the Auto-Scan (address 03) and follow the procedure for that version. Example: ABS pump 6R0614117P.

6R0614117 pumps – confirmed models

Pump numberConfirmed models
6R0614117KŠkoda Fabia II, Seat Ibiza IV (6J)
6R0614117PVW Polo V (6R), Škoda Fabia II, Seat Ibiza IV (6J)
6R0614117TVW Polo V (6R), Seat Ibiza IV (6J)

ABS pumps for other makes

For other makes, such as Opel, Ford, Renault, Suzuki or Honda, the requirements after a pump replacement vary: not every pump needs coding or adaptation with a tester. Bleeding the brake system is always necessary.

Before buying, send us the pump number and we will tell you what to expect. All models are in the ABS pumps category.

Frequently asked questions

Does a 1K0614517 ABS pump need coding after replacement?

Yes. MK60 and MK60EC1 pumps always need coding and sensor calibration on the car. It is best to transfer the coding from the old pump; how you code it depends on the module version.

Does a 1K0614517 pump fit a Golf VI, Audi A3 8P or Seat Leon II?

Yes, for example version 1K0614517DE is confirmed for the VW Golf VI, Audi A3 8P and Seat Leon II. However, the full pump and module numbers on the label decide the fit.

What do I code an ABS pump with in a VW, Audi, Seat or Škoda?

With VCDS. On MK60 you enter the coding, on MK60EC1 you do long coding. Then you calibrate the other sensors, and the G85 steering angle sensor always at the very end – otherwise the coding is erased when the ignition is switched off.

What if I do not have the coding from the old pump?

Check whether you have an earlier Auto-Scan of the car – you can enter the coding saved in it in the New Coding field. If you do not, pass a full Auto-Scan and the repair history to the technical support of your tool’s manufacturer. That is why you should always run an Auto-Scan before removing the old unit.

How do I check that an ABS pump fits my car?

Compare the module number (1K0907379…) and the pump number (1K0614517…) on the labels. If both are the same, including the letters, the pump fits – whatever the car model.

What is the most common fault in 1K0614517 pumps?

Most often the processor in the ABS control module fails. In refurbished pumps we replace it with a new one.

Can a 1K0614517BD pump replace a different version?

Only if your unit has the same pump number and the same module number. Different letters mean a different version. Send us a photo of both labels and we will check the match.

Are ECUSALE pumps checked?

Yes. Used pumps have their electronics and hydraulics checked, including a pressure test, and in both versions we test the sensors. The warranty is 6 months.

Where is an MK60 or MK60EC1 ABS pump coded?

On the car, after the pump has been fitted. MK60 and MK60EC1 pumps always need coding and sensor calibration.

What is the most common mistake after fitting an ABS pump?

Incorrect sensor coding or a badly performed pump calibration. Follow the steps in order and check the fault memory at the end.

Do ABS pumps from other makes need programming?

Not all of them. Some models need no calibration and work without programming. Send us the pump number before buying and we will tell you what to expect.

1K0614517 ABS pump ready to fit

We prepare the parcel within 24–48 working hours. Delivery takes 2–3 working days in the EU and 5–7 working days outside the EU. Warranty: 6 months.

See VW ABS pumps · Contact · How to buy

Comments on the post (0)

Write a comment

Automotive Electronics Manufacturers

ECU Engine Controllers, ABS Pumps, BCM Modules and automotive electronics.