FPT CNG ECU ENGINE CONTROLLER for Iveco Stralis Euro 6 - 5801971305 Metatron 4100314 –
The offered ECU ENGINE CONTROLLER 5801971305 Metatron 4100314 is an original control unit used in Iveco Stralis Euro 6 trucks with FPT engines adapted for CNG supply. The controller is responsible for managing the operation of the power unit, controlling natural gas injection, supervising exhaust emission parameters and communication with other vehicle modules via the CAN bus.
The Metatron 4100314 model was developed by FPT Industrial specifically for gas-powered trucks. The controller manages the CNG combustion process, optimizes the fuel dose and ensures correct operation of engine safety systems and OBD diagnostic systems used in vehicles meeting the Euro 6 emission standard.
The ECU ENGINE CONTROLLER 5801971305 is responsible, among others, for:
- control of CNG gas injection
- control of ignition and combustion parameters
- management of engine torque
- communication with vehicle modules (ABS, gearbox, EBS, safety systems)
- monitoring of engine sensors and exhaust emission systems
- OBD diagnostics and storing fault codes
In Iveco trucks, exact compatibility by part number is very important. In many Stralis models, different controller versions were used depending on the production year, engine power and vehicle configuration. Therefore, before purchase, you should always check the number from the label of the old controller.
Compatibility – which vehicles does controller 5801971305 fit?
The controller 5801971305 Metatron 4100314 is used in Iveco trucks equipped with FPT gas engines. It is most often found in the following models:
- Iveco Stralis NP – CNG-powered trucks
- Iveco Stralis Euro 6 – Natural Power gas versions
- Iveco Stralis NP 400 / NP 460
- Iveco Stralis Natural Power
The controller works with FPT Industrial power units adapted to run on CNG natural gas, most often with a displacement of:
- FPT Cursor 9 Natural Power
- FPT Cursor 13 Natural Power
Typical production years of vehicles using the Metatron 4100314 controller are approximately 2014 – 2020, however final compatibility should always be confirmed by part number 5801971305.
Why compatibility by number 5801971305 is crucial
In Iveco trucks, different ECU software configurations are used. The same vehicle model may have several different controller versions depending on:
- engine power
- exhaust emission standard
- CNG installation version
- gearbox
- vehicle equipment
Therefore, the most reliable selection method is always to compare the number from the label of the old module with the number 5801971305 Metatron 4100314.
FAQ – most frequently asked questions
Does controller 5801971305 Metatron 4100314 fit Iveco Stralis CNG?
Yes, controller 5801971305 is used in Iveco Stralis Natural Power vehicles with FPT engines adapted for CNG gas supply. Compatibility should be confirmed by the part number from the controller label.
For which Iveco engine is ECU Metatron 4100314 intended?
The controller Metatron 4100314 mainly works with FPT Cursor Natural Power engines used in Iveco Stralis NP Euro 6 trucks.
Does 5801971305 ECU work in Iveco Stralis Euro 6 Natural Power?
Yes, number 5801971305 is used in Iveco Stralis Euro 6 vehicles with CNG gas drive. However, it is important to match the controller by part number.
Does Metatron 4100314 fit Iveco Stralis NP 400 or NP 460?
The controller Metatron 4100314 is found in many Stralis NP vehicle configurations, including NP 400 and NP 460 versions. Compatibility should always be checked by ECU number.
Where is part number 5801971305 located in the Iveco controller?
Number 5801971305 is located on the label of the Metatron ECU controller. It is most often placed on the upper part of the module housing together with the manufacturer code and hardware number.
Does engine controller 5801971305 require programming after installation?
In most cases, Iveco engine controllers require adaptation or programming using service diagnostics such as Iveco EASY software or compatible diagnostic tools.
How do I check if ECU Metatron 4100314 fits my Iveco Stralis?
The most reliable way is to compare the part number of the old controller with the number 5801971305 Metatron 4100314. If the numbers are identical, the controller will be compatible with the vehicle.
Can controller 5801971305 exist in different software versions?
Yes, different ECU software versions are used in Iveco Stralis vehicles. Therefore, even with the same hardware number, different engine calibration configurations may exist.
